HOW TO INSTALL

WATCH THE VIDEO

HOW TO INSTALL

WATCH THE VIDEO
  • STEP 1
    Set

    Connect the Simple Mount™ brackets.
    Snap the brackets onto the back of the panel and
    slide the bracket until you hit the stopper.
    Please note: this should be done while
    the brackets are still off the wall.

  • STEP 2
    Level & Screw

    Position the assembly against the wall.
    Drive the anchorless screw into the first
    bracket hole above the panel.

  • STEP 3
    Snap & Click

    Snap the remaining panels in position,
    and admire your designer
    look that only took minutes!

The Three Steps

LEARN THE PARTS

  • BOTTOM BRACKET

    This bracket is uniquely designed with a stopper.
    It should be mounted on the very bottom
    of your configuration.

  • TOP BRACKET

    This should be aligned on top of your bottom bracket
    to continue your column of panels.

  • THE STOPPER

    This will be the most important part
    of your configuration. The stopper is designed to support the
    entire column of panels, and will prevent your panels from
    sliding down.
    Note: Do not remove the stopper from its original bracket
    due to its specificly designated location on the bottom bracket.

  • THE CONNECTOR

    This will connect the two half brackets so
    you get the desired hieght of four panels.

  • THE CAP

    This should be applied to the bottom and top
    ends of your brackets. They cover the raw alluminum
    edges for a finer look and feel.
    Note: Caps are only needed at the very top and
    bottom of each column.

Learn The Parts

VäNT RULE OF FOUR

Each box of Vant Panels is designed to be mounted in 1 column of 4 panels high, this will ensure that all your panels are fitted tightly with no gaps between the panels. With the uniquely designed stopper at the bottom, after the 4 base panels have been installed, you can then add panels above in groups of 2 or 4.
If you would like to add just 2 panels, simply stack the half of the bracket on the top of the existing brackets, (no connectors needed) and add the extra 2 panels to the next column.

If you wish to mount your panels in a different configuration, such as 3 panels high or a 2X2 configuration etc, see FAQs below.

VäNT RULE OF FOUR

Each box of Vant Panels is designed to be mounted in 1 column of 4 panels high, this will ensure that all your panels are fitted tightly with no gaps between the panels. With the uniquely designed stopper at the bottom, after the 4 base panels have been installed, you can then add panels above in groups of 2 or 4.
If you would like to add just 2 panels, simply stack the half of the bracket on the top of the existing brackets, (no connectors needed) and add the extra 2 panels to the next column.

If you wish to mount your panels in a different configuration, such as 3 panels high or a 2X2 configuration etc, see FAQs below.

Stacking 2 Above 4

When stacking additional panels on top of your configuration of 4,
you will not need more connectors.
Stoppers are also not necessary in this case,
as this new row will be held up by the panels below.
Just align the panels even with the bottom row and continue mounting
and place those end caps onto the topmost bracket to finish it all off!

  • NO STOPPER NEEDED

  • NO CONNECTOR NEEDED


2x2 Configuration

If you choose to mount your panels in a 2 x 2 configuration,
you would need to purchase an extra set of bottom brackets
to accommodate the 2nd row of panels.

These bottom brackets come with special stoppers,
to prevent the panels from sliding out.


No Studs Needed

The patented anchorless screws are designed with extra wide threads to grip the drywall
so the panels are firmly held in place.
No studs or anchors will be needed when mounting your panels onto drywall.

Each screw has the capacity to hold up to 50 lbs.

ANCHOR-LESS SCREW


Mounting 3 Panels High

Each aluminum bracket is designed to fit 2 panels. If you would
like to stack just one more panel (for a total of 3 or 5 panels high),
you would need to cut the bracket in half to fit that one extra panel.
Our brackets are made of aluminum, thus can easily be cut with just a Hack Saw.

HACK SAW


Clean VäNT

Dust regularly. As with all fabrics, avoid direct heat and sunlight.

Upholstered Care: spot clean with a damp white cloth.
Blot to remove excess water. Air dry, or consult with professional upholstery cleaner.

CLOTH


Cut-Out For An Outlet

Since the panel base is wood, you can do a cutout
from the back of the panel. The cutout should be the size of your electric switch/outlet box.
Then gently cut thru the upholstery, pull the box thru,
and place the outlet cover as you would normally do on a regular wall.

(Use a Jigsaw for wood cutout and a Razor knife for upholstery)


"I love it. Literally love it. I have told all my friends and family to buy one. If I could box it up and take it everywhere with me, I would..."

Sarah Bamberg, Age 29, Long Grove, IA

Free shipping

Free UPS delivery to your door
anywhere in the US

Please wait...

Continue shopping
View cart & checkout
Continue shopping
View cart & checkout